Home > Hardware Error > Hardware Error 0502 Lexmark X6100

Hardware Error 0502 Lexmark X6100

I have to say that my printer does the same thing with the paper grabs it on the side. http://experts.about.com/q/Printers-1512/lexmark-p4350.htm Reply flipa says: 2006-10-06 at 11:08 am Lexmark P3450 ah thanks but seen that page and tried everything! I went to the Dell site and got no help. Again, the back part of the printer casing goes in first, then the top front casing. http://jennysbookreview.com/hardware-error/hardware-error-0502-lexmark.php

I somebody has a more permanent solution, please post is here. I took the whole casing except the bottom off. This should take care of the printing problems…if not, then you may actually need a new printer. Thanks 🙂 Reply Anthony says: 2008-12-12 at 9:55 pm Thanks for the help; I use this machine now as a fax and back up printer; got the message a couple of http://support.lexmark.com/index?page=content&productCode=LEXMARK_X6150&segment=SUPPORTproductCode%3D&userlocale=ES_ES&id=SO3370

I have a P4350 Lexmark. ONE HAS A SENSOR IN IT WITH A LONG WIRE THAT COILS INTO A SPRING. Reply phoenix4591 says: 2007-12-02 at 10:16 pm Thanks - cleaning the metal rod, has solved the problem. Started when I innocently installed a new black cartridge ….

with picture included: Re-position the Encoder Strip on your Printer To re-position the encoder strip, perform the following steps: 1. The unit does not have a paper jam. Gently press the strip first to the rear and then forward to ensure that it is seated correctly. 7. I too found your site by googling Lexmark Hardware error 0502 after getting it twice…..I'm not one of those "go to the manufacturer first for good answers kind of people!" :

I just bought this thing. Now about the paper feed problem?? Reply Patricio says: 2009-08-27 at 11:48 pm I following the process exactly that you explain and works PERFECT!!! http://support.lexmark.com/index?page=content&id=SO2723 how do you get rid of them.

Reply Harold says: 2007-02-14 at 10:19 pm Advice on error 0502 seems to have worked on my dell A960. put power brick back in. Reply Deane says: 2009-02-03 at 2:17 am This was frigging brilliant!!! Wipe it down with a soft cloth gently, then slide the cartriges all the way to the right, and repeat this process.

Reply John says: 2007-09-26 at 2:52 am I tried cleaning both the rail and the encoder strip and still have the 0502 error. http://blog.forret.com/2006/02/11/lexmark-printers-with-hardware-error-0502/ I have a lexmark all in one. thx Reply DW says: 2006-11-20 at 2:29 pm Tried the paper towel trick on my Dell A10 A960 getting that error code. Oh, in case you didn't guess - THANK YOU!!!

wish i saw this site first! check my blog My ink was low so I changed it and then I started to get the 502 hardware error. I keep getting the message Error 1102. Out of desperation I found your solution.

Press the + button 4 times until Self test appears on the LED Display. 3. WHAT ELSE CAN I DO TO GET IT TO WORK. I need photos. http://jennysbookreview.com/hardware-error/hardware-error-0502-lexmark-x6150.php S.O.S Reply hzm says: 2008-10-19 at 3:04 pm i clean it but the problem still…when the ink move u hear a strong voice from it….help me plssssssssssssss Reply JEANNETTE says: 2008-10-20

Reply Min says: 2007-03-26 at 1:58 am Thank you mucho. It kept getting stuck when in the far left position but slid easily across the rest of the bar. Reply Mike Miller says: 2007-04-14 at 8:59 pm I'd cleaned the rod with a paper towel and a little WD 40.

This whole procedure might take you up to 30 minutes and it will not help (been there, done that).

Slightly push the encoder strip down and then back up to get it into the slot.• Lightly press the strip first to the rear and then forward, if necessary. No more Hardware Error: 0502. C'è stato un errore con l'applicazione. These printers were not that expensive, so may it is time.....I have cleaned the strip & metal bar in the past and I have been OK....then the issue began again.......so will

I accidentally knocked this out and had to find a hole where it goes back in. I would like to update this with an additional note to explain the hook on the right-hand side. Cleaning the metal bar seemed to fix the problem of freezing up when copying. http://jennysbookreview.com/hardware-error/hardware-error-0502-lexmark-printer.php X6100 Reply Joseph says: 2006-12-12 at 11:26 am ive tried wiping the strip and the metal rod, and still i continue to recieved this 502 error, just about to introduce this

says: 2006-03-29 at 10:05 pm hey guys. (if anyone is still here) if any of you took the time time to mess with the encoder strip, how didi you get it Reply shadow says: 2007-10-01 at 1:24 pm I found a thumb tap in mine .. Place an index finger on the encoder strip on either side of the cartridge carrier. 7. Many thanks again.